570r no reel speed - The Combine Forum
 1Likes
  • 1 Post By stser
 
LinkBack Thread Tools
post #1 of 6 (permalink) Old 08-30-2019, 09:04 PM Thread Starter
Junior Member
 
Join Date: Aug 2015
Posts: 2
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
570r no reel speed

Have a “new to me” 570r that came without headers. Hooked up to a honeybee sp30 today and everything works except the reel. So I hooked onto a precision P13 pickup and same result. Aeveeything works except what is fed from the two hydraulic lines on the combine. When I go to adjust the reel speed it displays “unable to adjust reel, front attachment does not support hydraulic adjustments”. Has anyone run into this issue before?

Hainesfarm is online now  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 08-30-2019, 11:45 PM
Senior Member
 
seedcleaner's Avatar
 
Join Date: Nov 2007
Location: Mid-Missouri
Posts: 2,517
Mentioned: 0 Post(s)
Quoted: 392 Post(s)
Probably an issue with the multi point coupler. I think a wire or two will need jumped so the combine realizes it is hooked to a header that needs a reel powered.

seedcleaner is offline  
post #3 of 6 (permalink) Old 08-31-2019, 03:20 AM
Senior Member
 
Darcy's Avatar
 
Join Date: Sep 2010
Location: WC Sask
Posts: 489
Mentioned: 0 Post(s)
Quoted: 57 Post(s)
And Check below the unloading auger. There is a sensor with linkage that is connected to a hyd valve. Make sure it’s connected. For future reference there is a brass bushing on the linkage bolt on the valve. It should be replaced every few yrs
Darcy is offline  
Sponsored Links
Advertisement
 
post #4 of 6 (permalink) Old 08-31-2019, 10:07 AM
Senior Member
 
Join Date: Jun 2012
Location: east central Alberta
Posts: 1,283
Mentioned: 0 Post(s)
Quoted: 259 Post(s)
Quote:
Originally Posted by seedcleaner View Post
Probably an issue with the multi point coupler. I think a wire or two will need jumped so the combine realizes it is hooked to a header that needs a reel powered.
Did both headers that you bought have the 500 series multipoint connectors on them? As seedcleaner suggests you have to have an input from the reel speed sensor. You may have to change the sensor to get the right voltage range for a Lexion if the header came from a different brand. Lex runs a 5 volt system IIRC and others are different. I mounted a HB header on a 480 and had to add the right speed sensor and then get the wiring on the header to the multiport to match up with the combine side. It could be other problems like a reel speed module or in the electric over hydraulic flow control system. I have seen those but check your header wiring first.
Transaxial is offline  
post #5 of 6 (permalink) Old 08-31-2019, 11:23 AM
Junior Member
 
Join Date: Nov 2018
Location: East Central SK
Posts: 4
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
I had this exact problem on my new to me 570r last fall. We purchased a Macdon D50 that came off a JD. So I bought a used lexion adaptor and swapped it over. Never tried reel speed until it was time to harvest. With the machine running and someone in the cab, we unhooked the linkage on the left hand side and manually moved it to make sure the reels speed up and slowed down like it was supposed to. I ended up unhooking and hooking the connection from combine to header a few times with the key on and engine running (machine not engaged) and it ended up starting to work and worked perfect all year. Not sure if it was fluke or if the unhooking and hooking up made it realize there was a header on it. Lexion dealer said I needed wiring and a new reel speed sensor as my header came off a JD, but that was not the case for us.
Transaxial likes this.
stser is offline  
post #6 of 6 (permalink) Old 09-02-2019, 12:52 PM
Senior Member
 
Jeff-C-IL's Avatar
 
Join Date: Jul 2015
Posts: 1,122
Mentioned: 0 Post(s)
Quoted: 204 Post(s)
YOu don't need a reel speed sensor---many Lexions running conversions w/o. WHat you DO need is the "reel drive loop" on the header multilink. THis is a connection that loops a 12V signal back into another pin to tell the combine to enable reel drive. XB-9 is the 12V source. XC-5 is the reel enable pin. They have to be connected for the reel to turn. I'm attaching a print which may help....try testing continuity between the pins on the head.

Did you convert both of your heads to Lexion? If so, you probably need to connect a couple little pins together somewhere by the multilink. If these heads previously worked on a Lexion, I'd check your combine wiring.
Attached Files
File Type: pdf CA500ML r6.pdf (71.2 KB, 7 views)

AHHC specialist
Jeff-C-IL is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the The Combine Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome