The Combine Forum - View Profile: ktmray

ktmray ktmray is offline

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 3 of 3
  1. Kristnovo
    09-05-2015 12:19 AM - permalink
    Hey I seen in a post of yours you described a problem with your 8010 and a rotor rtf clutch valve issue. We're having a similar problem and I'm hoping you can shed some light on what's going on.

  2. ktmray
    09-28-2014 01:04 PM - permalink
    my combine didnt have the control pressure sensor relocated- when we changed that out we havnt had any further issues-i think wiring might have been part of the problem--i bypassed the harness that goes from the connector under the grain tank through the hydraulic (stuff) coming off en of engine and havnt had anymore control pressure issues--a big headache for the past 3 years
  3. matt
    09-08-2014 10:22 AM - permalink
    need info on what u did to fix control pressure problem on tour 8010 I have same problem

  About Me

  • About ktmray
    east central alberta


Total Posts
Visitor Messages
General Information
  • Last Activity: 11-10-2019 02:25 AM
  • Join Date: 08-29-2013
  • Referrals: 0


No results to display...


01:18 AM - Farmermb quoted ktmray in post Valterra & Fierce
Anybody used much of these?...
01:09 AM - scottyheps quoted ktmray in post Fd135 feeding issue
Peas are flipping over the ...
12:44 PM - garyfunk quoted ktmray in post What’s a good alfalfa- grass mix for hay
Would like to put some hay ...
11:06 AM - SWMan quoted ktmray in post Trading rigid macdon header on macdon flex
Thanks for input- so sw I g...
03:59 AM - iksn quoted ktmray in post Viper carryover?
Does BASF still tell you it...
03:07 PM - brazil08 quoted ktmray in post Round up ready canola vs invigour
Thanks for responses- invig...
02:45 PM - Twix quoted ktmray in post Round up ready canola vs invigour
Thanks for responses- invig...
01:01 AM - kevlar quoted ktmray in post Hypro Pump on Spray Coupe 7660
I feel your pain- transorb ...
10:47 AM - ktmray quoted madsnake in post 7650 Spra Coupe ECM
.... Good luck Madsnake is ecm grounded t...
03:10 AM - BrianTee quoted ktmray in post Openers
How critical is fracturing ...
02:21 AM - Gleanermechanic340 quoted ktmray in post 8680 combine u joint on clean grain elevator
does u joint thread into cl...
01:52 AM - ktmray quoted tkwfarms in post header height issues
Our 2388 decided the header h...
01:38 AM - ktmray quoted puddles in post header drop rate
think I got it thanks for re...
12:07 PM - joesixpack quoted ktmray in post wild oats in canola
no that was my own sampling...
01:14 AM - ktmray quoted wetfarmer in post Unplugging the APS
Wow this brings back bad memor...
01:09 AM - ktmray quoted nicemustang in post 8010 canola settings
Not real sure, sometimes we run ...
11:47 AM - ktmray quoted nicemustang in post 8010 canola settings
I think you have lots wrong! Try...
01:03 AM - ktmray quoted kirschenman in post How to set 8010 for very dry canola
You have some pieces to buy that...
09:49 PM - ilbar quoted ktmray in post 2010 wd1903 reel speed issues
knife speed is good, i'm ju...
For the best viewing experience please update your browser to Google Chrome