'SUPER' 9770 with ICC <<<<now with part #'s>>>> - The Combine Forum
Reply
 
LinkBack Thread Tools
post #1 of 22 (permalink) Old 08-06-2009, 11:56 AM Thread Starter
Senior Member
 
Join Date: Jan 2006
Posts: 588
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
'SUPER' 9770 with ICC <<<<now with part #'s>>>>

We installed all the necessary parts to add the additional pre-cleaner to our 9770...it bolts right on. Essentially it makes the 9770 into a 9870 sans the big motor.
In our conditions in wheat, we were a shy on shoe capacity (wonder why) as opposed to power or rotor loss. I looked at all the part numbers and the ICC bolts right on to any of the smaller combines.
Much ( not really, I expected this) to my surprise, ALL the fan drive parts are identical on all the machines. The higher fan speed on the 98 is achieved my adjusting the lock nuts on the screw adjuster and voila, more speed. We also added the revamped windboard to ensure that everything was EXACTLY like a 98.
Long story short, for about $1500 we have the exact threashing and cleaning of a 9870 in a 9770. It does allow us to travel faster in high yielding wheat, so it was a good addition.

kinzepower is offline  
Sponsored Links
Advertisement
 
post #2 of 22 (permalink) Old 08-06-2009, 12:13 PM
Senior Member
 
Join Date: Jun 2005
Posts: 342
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC

We run two 9770s. Curious, what are your settings and how fast are you cutting in what kind of yields. We cut some winter wheat and I averaged around 4.5 mph in 40-60 bu with a 36ft header. If field conditions were good I got up to 5 mph. Capacity hasn't been a problem except I get rotor loss before I get shoe loss. My settings are 830 on the fan, 860 on the rotor, concave at 10, top chaffer 16 and bottom sieve 5 with no filler plates or bands anywhere on the concave.

jd95guy is offline  
post #3 of 22 (permalink) Old 08-06-2009, 12:53 PM Thread Starter
Senior Member
 
Join Date: Jan 2006
Posts: 588
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC

We typically have 100+ bushel wheat with short straw and our shoe loss has been limiting.
With the addition of the ICC both shoe and rotor loss are similar so we can go about 10% faster on average and keep loses less than 1%
We have a 630 flex and travel about 3.5mph.
If shoe loss is not an issue, this would not benefit.

I forgot to add, we use the round bar concaves with 3 sets of interupter bars and with this setup we have greatly increased separation which has led to the shoe being limiting. In our wheat, the small wire was too restrictive and thus carried too much wheat further back the rotor.
kinzepower is offline  
Sponsored Links
Advertisement
 
post #4 of 22 (permalink) Old 08-08-2009, 10:17 AM
jmt
Member
 
Join Date: Sep 2008
Posts: 39
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC

kinzepower, did you also have to add the left hand side shoe drive that the 9870 has ?
jmt is offline  
post #5 of 22 (permalink) Old 08-08-2009, 04:01 PM
Junior Member
 
Join Date: Aug 2009
Posts: 28
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC

we will see how good it worked in a month when we see the green runways.
greenreseeder is offline  
post #6 of 22 (permalink) Old 08-23-2009, 12:33 PM
Senior Member
 
Join Date: Jul 2007
Posts: 578
Mentioned: 0 Post(s)
Quoted: 4 Post(s)
Re: 'SUPER' 9770 with ICC

does anyone have the part no.s for this update?? can it be added to older sts's?
brewmax is offline  
post #7 of 22 (permalink) Old 09-14-2009, 05:34 PM Thread Starter
Senior Member
 
Join Date: Jan 2006
Posts: 588
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC

AH223121 - CHAFFER
AH223122 - BRACKET X 2
H225940 - PARTITION X 3
H224488 - PARTITION X 3
AH212262 - SHEET
05616663 - GROMMET 16mm
plus a handful of fasteners

The entire parts bill was $1200 canadian...WELL worth it IMHO.
kinzepower is offline  
post #8 of 22 (permalink) Old 09-14-2009, 10:20 PM
Senior Member
 
Join Date: Jul 2007
Posts: 578
Mentioned: 0 Post(s)
Quoted: 4 Post(s)
Re: 'SUPER' 9770 with ICC <<<<now with part #'s>>>

does it work on older series?
brewmax is offline  
post #9 of 22 (permalink) Old 09-15-2009, 06:31 AM Thread Starter
Senior Member
 
Join Date: Jan 2006
Posts: 588
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC <<<<now with part #'s>>>

Maybe late 60 series, have to check to see if the chaffer frame # is the same as the 9870.
kinzepower is offline  
post #10 of 22 (permalink) Old 09-17-2009, 10:31 PM
Senior Member
 
Join Date: Nov 2007
Location: Fairview, MT
Posts: 400
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 'SUPER' 9770 with ICC <<<<now with part #'s>>>

you can probably get it to work, but it will not bolt right in.

there will be drilling involved

ststech is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the The Combine Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
<<FOR SALE>>AMADAS edible bean kit/belt unloader for STS SpudManMax For Sale/Want to Buy 1 02-01-2014 03:23 PM
&gt;&gt;&gt;DUALS FOR SALE&lt;&lt;&lt; CHEAP SHIPPING TO MIDWEST kinzepower For Sale/Want to Buy 3 08-07-2010 09:45 AM
Update on 9770 with ICC kinzepower John Deere 2 07-27-2010 07:15 PM
PICS&gt;&gt;&gt;&gt;&gt;Just something neat! factoryfarmer Other / Off Topic 3 02-09-2010 09:50 PM
&gt;&gt;&gt;&gt;&gt;DUALS FOR SALE&lt;&lt;&lt;&lt;&lt;&lt;&lt; NOT A DEALER :) kinzepower For Sale/Want to Buy 1 10-17-2009 06:38 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome