8010 In the Cove - Page 3 - The Combine Forum
Reply
 
LinkBack Thread Tools
post #21 of 122 (permalink) Old 02-26-2006, 11:01 PM Thread Starter
98j
Senior Member
 
Join Date: Feb 2006
Posts: 1,053
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

Quote:The header looks like a Case made by Honeybee.

Hmmmm.....then I guess that the MacDon rep that
came by to check on it must have been REALLY lost.

98j is offline  
Sponsored Links
Advertisement
 
post #22 of 122 (permalink) Old 02-27-2006, 01:03 AM
Junior Member
 
Join Date: Feb 2006
Posts: 4
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

8950 The mirrors are a safety item also. I can keep an eye on the truck drivers while I am unloading. Just to make sure no one has walked in tight to the machine.

steep is offline  
post #23 of 122 (permalink) Old 02-27-2006, 07:10 AM
Junior Member
 
Join Date: Jan 2006
Posts: 7
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

macdon round tube backbone of header n honeybee is squared tube
noskire is offline  
Sponsored Links
Advertisement
 
post #24 of 122 (permalink) Old 02-27-2006, 12:08 PM
Senior Member
 
Join Date: Dec 2005
Posts: 809
Mentioned: 0 Post(s)
Quoted: 2 Post(s)
Re: 8010 In the Cove

How do you run that thing without auto header contols? That means the operator is manually tilting the header as well as controling the height. What mph do you run when cutting? You can see in the pictures how nice it is to run a draper on a rotary combine when there's no cross auger dust in front of you
midwest is offline  
post #25 of 122 (permalink) Old 02-27-2006, 04:31 PM
Senior Member
 
cogleaner's Avatar
 
Join Date: Nov 2005
Posts: 371
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

Quote:
Quote:The header looks like a Case made by Honeybee.

Hmmmm.....then I guess that the MacDon rep that
came by to check on it must have been REALLY lost.


Maybe I'm lost....sorry
cogleaner is offline  
post #26 of 122 (permalink) Old 02-27-2006, 04:37 PM
Senior Member
 
rother's Avatar
 
Join Date: Dec 2005
Posts: 246
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

Case IH's headers are made by MacDon. Infact, if you look, the adapter to the 8010 will alot of the time say MacDon instead of Case IH on it. They have been doing this since I believe 04 when the first 8010s came out.
rother is offline  
post #27 of 122 (permalink) Old 02-27-2006, 08:05 PM
Junior Member
 
Join Date: Jan 2006
Posts: 7
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

case have got toes in both camps.....macdon make the draper headers for the 2300's and 8010 and case have honeybees and their draper equiped self propelled windrowers sourced from new holland
noskire is offline  
post #28 of 122 (permalink) Old 02-27-2006, 10:53 PM
Senior Member
 
Join Date: Dec 2005
Posts: 3,334
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

same way you would cutting beans

hit the tilt button a heck of alot

lol

(on how do you do that manually without auto header)

sure is fun in hilly terrain with a 1020 bean head cutting beans too
casefarmer is offline  
post #29 of 122 (permalink) Old 02-28-2006, 12:06 AM Thread Starter
98j
Senior Member
 
Join Date: Feb 2006
Posts: 1,053
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Re: 8010 In the Cove

Quote:How do you run that thing without auto header contols? That means the operator is manually tilting the header as well as controling the height. What mph do you run when cutting? You can see in the pictures how nice it is to run a draper on a rotary combine when there's no cross auger dust in front of you
Hey Midwest! Well, duh on my part! I didn't explain this
very well...a hillside combine tilts the header automatically..the 8010 uses a master/slave cylinder set
up..the master is set on the main axle...as the separator
levels, the slave cylinder keeps the header parallel to the ground, so the operator does not have to manually
tilt the header. He can trim manually when needed, like
when the machine exceeds the max level of 27%. Older
Hillside machines like the 1670 that I run use a simple
cable set up to tilt the header ( ie as the left side driver
goes down, the cable pulls down the left side of the
platform) The down side to this old system is that there
is no trim.
As for the height control...well it turns out that I lied
to you..Steep set me straight this AM. When the MacDon rep was here, he extracted the right stuff from the software and enabled the height control that works
off pressure at the feeder house....set the height manually, punch the button and presto! Auto height
control. And our boy Steep used it....some. Since the
height is governed at the feeder house and not out at the cutter bar, he had to override when crossing a draw
for example....raise the header, get across the draw , then reset the height. Not quite as handy as an auto
control using either radar or a potentiometer.
So a long winded answer that boils down to this:
The tilt is auto....and it does have auto height....and
before we get done it will probably have a different
auto height control. Hopefully, Steep will show up on here in the next couple of days and give you an even
better answer... in the meantime....a shot of the main
axle under the 8010....two leveling cylinders left and right and the platform tilt master in the center.

98j is offline  
post #30 of 122 (permalink) Old 02-28-2006, 09:12 AM
Senior Member
 
Join Date: Dec 2005
Posts: 809
Mentioned: 0 Post(s)
Quoted: 2 Post(s)
Re: 8010 In the Cove

Thanks, I was thinking that the operator would need ESP and one heck of a thumb to run that thing all day. Neat pictures and a neat setup.

midwest is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the The Combine Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
8010 or 9870 gracevalley John Deere 3 07-29-2010 04:35 AM
Afx 8010/8010 bms26 Case IH 0 11-15-2009 01:16 PM
9860 to 8010 screamin9860974 John Deere 3 10-04-2009 10:54 AM
'07 8010 vs. '08 8010 casecombine25 Case IH 8 02-19-2009 07:00 PM
Re: old 8010 and new 8010 - how is bin different? bleedred Case IH 8 09-09-2007 08:15 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome