The Combine Forum - View Profile: Tin Man

Tin Man Tin Man is offline

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 1 of 1
  1. Jeff-C-IL
    08-13-2019 05:26 PM - permalink
    Jeff-C-IL
    Was looking thru my notifications and realized this message had never been answered?? The answer is yes, if you run the head on the wheels with the float unlocked. The AHC and tilt can work with the wheels carrying the head, just like with the head sitting on the ground.

    Sorry I missed this!

  About Me

  • About Tin Man
    Location
    Bonnie IL
    Interests
    Farming - Waterfowl Hunting
    Occupation
    Mechanical plumbing & piping Contractor

  Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Today 07:52 AM
  • Join Date: 09-12-2010
  • Referrals: 1

  Mentions

No results to display...

  Quotes

09-19-2019
08:49 AM - schaferag quoted Tin Man in post 9250 problem. Again.
Ran a 35' 9250 for 4 or 5 ye...
09-18-2019
10:20 PM - BMC quoted Tin Man in post 9250 problem. Again.
Ran a 35' 9250 for 4 or 5 ye...
08-29-2019
02:59 PM - Tin Man quoted glennw in post S 97 help
Yes it's the main belt. The...
08-28-2019
09:33 PM - glennw quoted Tin Man in post S 97 help
The spring that glennw has p...
08-07-2019
11:44 AM - SWMan quoted Tin Man in post 2020 lexion
Does the one machine have a ...
08:18 AM - adsinaus quoted Tin Man in post 2020 lexion
Does the one machine have a ...
07:58 AM - Don Boles quoted Tin Man in post 2020 lexion
Does the one machine have a ...
07:39 AM - Tin Man quoted SWMan in post 2020 lexion
Big boy at the 6:00 mark. ...
06-19-2019
04:54 PM - Tin Man quoted stevemcil in post Combine Won't Start
Getting geared up to mud out t...
11:04 AM - Tin Man quoted silverrod in post Smart Cooling Sensor Low Voltage
...sie distributor. silverrod, I was wrong, looked...
06-04-2019
12:57 PM - Transaxial quoted Tin Man in post Smart Cooling Sensor Low Voltage
Some good news. I got the ma...
05-13-2019
09:39 AM - Don Boles quoted Tin Man in post High speed chopper knives
So I got the Kondex knives F...
05-10-2019
09:16 AM - Tin Man quoted Snipe in post Accelerator Roll Shaft
...ailure using it. Snipe, I am not familiar w...
05-07-2019
11:17 PM - Don Boles quoted Tin Man in post High speed chopper knives
chopper is spinning 3200 rpm...
10:07 PM - Don Boles quoted Tin Man in post High speed chopper knives
I don't see where Redekop ha...
12-20-2018
03:59 PM - dpilot83 quoted Tin Man in post Longer S67 auger, gate for clean out, etc
I put an extension on my R72...
08:32 AM - dpilot83 quoted Tin Man in post 45 ft Mac don on a R76
There are products out there...
12-14-2018
02:30 PM - Tin Man quoted kentfarmer in post New Draper Header Thoughts
...switch Brands? kentfarmer, get a MacDon. I had...
12-11-2018
12:21 PM - Don Boles quoted Tin Man in post 9250 advice
So back to my question, does...
11:42 AM - Tin Man quoted Don Boles in post 9250 advice
You’re not wrong, no MacDon in...
 
For the best viewing experience please update your browser to Google Chrome