The Combine Forum banner
1 - 3 of 3 Posts

·
Registered
Joined
·
44 Posts
Discussion Starter · #1 ·
Is there anywhere i can find a full list of error codes and there fixes for 50/60 series sts. There is some in the operators manuel, but not enough, or any answers where the problems can be found
I currently have a machine on a job around 100 miles from the nearest dealer and John Deere dealers in Australia charge $100 /hr for travel time and $1.50/ Kilometer ($2.40/mile) each way. So just to get a technition to the job would cost almost $1000. That may be just to fix a broken wire.
The problem this machine has, is that when you turn the lights on, the corner post goes out, and with the ignition turned off and all the lights turned off, the tail lights are still on.
 

·
Premium Member
Joined
·
1,236 Posts
There is alot of codes for different controlers. Here is the C03
--------------------------------------------------------------------------------

Codes - C03 - Cornerpost Control Unit Diagnostic Trouble Codes
-: C03 - Cornerpost Control Unit Diagnostic Trouble Codes

Control Unit
SPN
FMI
Pri.
Description
Go To Section
Go To Group

C03
63
09
3
CAN bus message missing from control unit E13 (VCM) - feed rate.

Check diagnostic address C03 133 first and turn off feed rate option if feed rate option is not installed.
240
CAN Bus Diagnostics.

C03
96
09
3
CAN bus message missing from right control unit - fuel level.
240
CAN Bus Diagnostics.

C03
110
09
3
CAN bus message missing from engine control unit - engine coolant temperature.
240
CAN Bus Diagnostics

C03
190
09
3
CAN Bus message missing from engine control unit - engine speed.
240
CAN Bus Diagnostics

C03
627
03
3
Delayed power (cc# 006) voltage out of range high - greater than 16 VDC.
240
Alternator and Battery Diagnostics

C03
628
12
1
Controller cannot exit boot block program. Disconnect effected control unit connectors. Wait 30 seconds. Reconnect connectors. Reprogram controller with latest software. Replace control unit if condition persists.

C03
630
11
1
EEPROM failed test at power up. Replace cornerpost control unit if condition persists.

C03
639
19
3
CAN bus messages are not being transmitted or received correctly. Possible effects are none, slow response, or machine down.
240
CAN Bus Diagnostics

C03
1079
03
3
Concave position sensor supply voltage high - greater than 5.5 VDC.
240
Cornerpost - Threshing Clearance Diagnostics

C03
1079
04
3
Concave position sensor supply voltage low - less than 4.5 VDC.
240
Cornerpost - Threshing Clearance Diagnostics

C03
1486
03
3
Concave position sensor voltage is too high - greater than 4.5 VDC.
240
Cornerpost - Threshing Clearance Diagnostics

C03
1486
04
3
Concave position sensor voltage is too low - less than 0.5 VDC.
240
Cornerpost - Threshing Clearance Diagnostics

C03
1487
03
3
Dimmer voltage is too high - greater than 4.5 VDC.
240
Lighting - Panel Lights Diagnostics

C03
1487
04
3
Dimmer voltage is too low - less than 0.5 VDC.
240
Lighting - Panel Lights Diagnostics

C03
1492
08
3
Cab interior backlighting output transistor detects an open, short, over voltage, or over temperature condition.
240
Lighting - Panel Lights Diagnostics

C03
1493
09
3
CAN bus message missing from master tailings sensor - tailings volume.
240
CAN Bus Diagnostics

C03
1500
11
3
A switch on cornerpost display unit 1 is closed for longer than 30 seconds.
240
Cornerpost Control Unit Overall Diagnostics

C03
1501
11
3
A switch on cornerpost display unit 2 is closed for longer than 30 seconds.
240
Cornerpost Control Unit Overall Diagnostics

C03
1502
11
3
A switch on cornerpost display unit 3 is closed for longer than 30 seconds.
240
Cornerpost Control Unit Overall Diagnostics

C03
1503
09
3
CAN Bus message missing from armrest control unit - armrest switch status.
240
CAN Bus Diagnostics

C03
1510
09
3
CAN bus message missing from right control unit - combine temperatures.
240
CAN Bus Diagnostics

C03
1511
09
3
CAN bus message missing from right control unit - grain loss.
240
CAN Bus Diagnostics

C03
1515
09
3
CAN bus message missing from header control unit - header data.
240
CAN Bus Diagnostics

C03
1552
03
3
CLIMATRAK temperature setpoint adjust voltage too high - greater than 4.5 VDC.
240
CLIMATRAK Diagnostics

C03
1552
04
3
CLIMATRAK temperature setpoint adjust voltage too low - less than 0.5 VDC.
240
CLIMATRAK Diagnostics

C03
1552
13
3
CLIMATRAK temperature setpoint adjust not calibrated.
240
Calibration Procedures

C03
1553
03
3
CLIMATRAK fan speed adjust voltage too high - greater than 4.5 VDC.
240
CLIMATRAK Diagnostics

C03
1553
04
3
CLIMATRAK fan speed adjust voltage too low - less than 0.5 VDC.
240
CLIMATRAK Diagnostics

C03
1553
13
3
CLIMATRAK fan speed adjust not calibrated.
240
Calibration Procedures

C03
1565
09
3
CAN bus message missing from armrest control unit - separator and header engage status.
240
CAN Bus Diagnostics

C03
1567
09
3
CAN bus message missing from header control unit - control mode.
240
CAN Bus Diagnostics

C03
100100
09
3
CAN bus message missing from left control unit - system data.
240
CAN Bus Diagnostics

C03
100101
09
3
CAN bus message missing from left control unit 2 - system data.
240
CAN Bus Diagnostics

C03
100106
11
3
A switch on cornerpost display unit 4 is closed for longer than 30 seconds.
240
Cornerpost Control Unit Overall Diagnostics
 

·
Registered
Joined
·
44 Posts
Discussion Starter · #3 ·
Thanks deerefixer and motram
I have a fare list of codes
I should also point out that the machine developed this problem while driving on the road with the flashers on between jobs.
Codes are as follows:
C03 96.06
C03 110.09
C03 190.09
C03 1493.03
C03 1511.09
C03 1515.09
E03 2001 49.11
E03 2001 34.11
E03 2001 32.11
E03 2001 33.11
E03 1503.09
C00 158.04
C00 627.04
C00 1498.11

With this many codes one would thing of a electrical short some where, but where would you start to look.
 
1 - 3 of 3 Posts
Top